300°F | Vibra-Tite
-

Vibra-Tite 111 Low Strength Threadlocker
A low strength anaerobic threadlocker designed for locking threaded fasteners smaller than 1/4” in diameter, which require disassembly with standard hand tools. Also works on set screws, and screws that have a long engagement length.
-
Vibra-Tite 121 Medium Strength Threadlocker
A medium strength anaerobic threadlocker designed for locking threaded fasteners from 1/4” to 3/4” in diameter, that require disassembly with standard hand tools. Exhibits good temperature and solvent resistance.
-
Vibra-Tite 122 Oil Tolerant Threadlocker
A medium strength, oil tolerant anaerobic threadlocker designed for locking threaded fasteners from 1/4'' to 3/4'' in diameter, that require disassemble with standard hand tools. Exhibits good temperature and solvent resistance.
-


Hot
Vibra-Tite 125 Medium Strength Gel Threadlocker
A medium strength anaerobic gel threadlocker designed for locking threaded fasteners from 1/4” to 3/4” in diameter, that require disassembly with standard hand tools. Exhibits good temperature and solvent resistance. No-drip gel formula.
-
-

Vibra-Tite 135 High Strength Gel Threadlocker
A high strength anaerobic gel threadlocker designed to permanently lock fasteners up to 1” in diameter. Exhibits good temperature and solvent resistance. No-drip gel formulation makes it easy to apply.
-
Vibra-Tite 140 High Strength Threadlocker
A high strength anaerobic threadlocker designed to permanently lock fasteners. Exhibits good temperature and solvent resistance. Performs on aluminum, steel, plated, stainless steel, and special alloy parts. Locks and seals fasteners from up to 1'' in diameter.
-
Vibra-Tite 141 High Strength Threadlocker
A green general purpose threadlocker for permanent locking of threaded assemblies. 141 works on fasteners up to 1″ in diameter and seals against leakage and corrosion. It resists attack from most fuels, lubricants and industrial gases.
-
-
-

Vibra-Tite Viz-Torque® 202
Viz-Torque 202 Tamper Detection Marker is an inspection paste used to visually detect torque movement due to vibratory loosening or tampering of fittings, assemblies, nuts, bolts and studs. This quick-drying tamper proof torque marker identifies whether a part has been moved from its original position. Once dried in place, Viz-Torque 202 Tamper Detection Marker creates a seal for torque movement detection, which allows the dry and brittle material stripe to break, providing proof of fastener tampering or loosening. Viz-Torque 202 has good adhesion to most metals when applied to a clean, dry surface and is available in a selection of highly visible colors.
-
-
Vibra-Tite 225 No-Mix Structural Adhesive
An activated Acrylic adhesive designed for fast fixturing on metal and ceramic materials. Applications include bonding metal or ceramic close fitting rigid parts which are exposed to thermal cycling, like motor assemblies.
-
Vibra-Tite 250 Doming Plastics Light Cure Adhesive
Vibra-Tite 250 is a single component, medium viscosity UV coating and structural adhesive suitable for bonding glass to glass or glass to plastic. It is suitable for use as a doming resin on glass and some plastics and composites. This product cures when exposed to ultraviolet radiation. When cured, it is highly resistant to vibration and impact forces.
-
-
-
Vibra-Tite 420 Controlled Strength Thread Sealant
An anaerobic thread sealing and thread locking compound with PTFE for pipe fittings. It is designed for sealing threaded fasteners that require disassembly with standard hand tools. It exhibits good temperature and solvent resistant.
-
-
Vibra-Tite 486 Non-Hardening Thread Sealant
Vibra-Tite 486 Non-Curing Thread Sealant with PTFE is a creamy white paste for general purpose pipe and thread sealing. Typical applications include sealing threaded pipes, pipe fittings and flanges to seal against liquids and gases.
-
Vibra-Tite 530 General Purpose Retaining Compound
The product performs on aluminum, steel, plated, stainless steel, and special alloy parts. Can be used where lubricity is needed to press fit parts or to create an air-tight seal on cylindrical assemblies. This product cures rapidly on all metal surfaces. Replaces press fit assemblies and keyways. Used on gearbox bolts / drive shaft, bearing applications.
-
-
-
Vibra-Tite 542 High Strength – Large Gap Retaining Compound
A high strength, high viscosity, anaerobic retaining compound used for bonding rigid assemblies of all types. This material can be used effectively to increase the strength of most mechanical assemblies. Locks keys and splines. Eliminates backlash in worn assemblies. Locks bearings in place, preventing spin out. Bonds rotor to shaft in low horsepower motors. Locks bushings and sleeves in housings.
-
Vibra-Tite 546 Impact Resistant Retaining Compound
A quick fixturing high strength flexible, anaerobic retaining compound designed to bond metal cylindrical assemblies. Exhibits excellent temperature and solvent resistant. The product performs on aluminum, steel, plated, stainless steel, and special alloy parts. Locks shaft and hubs together for gears, bearing, bushings. Bonds pins, adaptors, plugs.
-
Vibra-Tite 709 Flexible Gasket Maker
Provides resistance to low pressures after assembly of flanges. Seals between rigid metal surfaces and flanges such as valve covers and gearbox casings. Can be used with or without pre-cut, pre-formed gaskets.
-
Vibra-Tite 724 Fast Flange Sealant Gasket Maker
Single component, medium strength, thixotropic, anaerobic sealant. Provides a fast low pressure seal between rigid metal faces and flanges and is suitable as a replacement for a variety of pre-formed or pre-cut gastkets. The thixotropic behavior of this material minimizes migration of material following application.
-
Vibra-Tite 730 Flexible Solvent Resistant Gasket Maker
High viscosity, single component, medium strength, thixotropic, anaerobic sealant which cures when confined between close fitting metal surfaces. Provides an instant low pressure seal. Seals joints between rigid metal faces and flanges such as valve covers and gearbox casings.
-
Vibra-Tite 732 Flexible Gasket Maker
A tough flexible formed-in-place gasket. Provides an instant low pressure seal. For fuel and water pumps, split crank cases on engines, gearbox covers, engine thermostats, air compressor end caps, chainsaws, lawn mowers etc.
-
Vibra-Tite 911 Epoxy
Epoxy VIBRA-TITE 911 is a fast setting adhesive that cures at temperatures as low as 41°F/5°C. For bonding and repairing small parts. Competes with Fastweld 10
-
Vibra-Tite 915 Epoxy
VIBRA-TITE 915 is a low-viscosity general purpose potting compound that is designed to form a resilient, long work time potting compound with good surface finish and bond strength to thermoplastics. Competes with Hysol E-60NC
-
Vibra-Tite 920 High Peel / High Shear 2 Part Epoxy
Vibra-Tite 920 is a medium viscosity, industrial grade epoxy adhesive with extended work life. This system forms a good adhesion to thermoplastics with high peel and shear strength. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.
-
Vibra-Tite 921 Plastic Bonding Epoxy
Vibra-Tite 921 is a medium viscosity, industrial grade epoxy adhesive with extended work life. This system forms a good adhesion to thermoplastics with high peel and shear strength. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.
-
Vibra-Tite 923 Aluminum Bonding Epoxy
Vibra-Tite 923 is a toughened, medium viscosity, industrial grade epoxy adhesive. Once mixed, the two component epoxy cures at room temperature to form a tough, off-white, bond line that provides high adhesive strength.
-
Vibra-Tite 924 Epoxy
Vibra-Tite 924 is a general purpose, medium viscosity, two-component epoxy adhesive system used for applications which require strong, durable, chemically and environmentally resistant bonds, high viscosity, with an extended work life. This system forms a resilient, long work time adhesive with an easy mix ratio and good adhesion to thermoplastics. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance. Competes with Lord 305
-
-
Vibra-Tite 932 Encapsulating Epoxy
Vibra-Tite 932 is two-part epoxy encapsulant and adhesive. This system forms a resilient, long work time potting and encapsulant material with an easy mix ratio and good adhesion to thermoplastics. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.
-
Vibra-Tite 933 Ignition Coil Impregnation and Encapsulation Epoxy
Vibra-Tite 933 is a long working life, heat curing, and two component formulation. It was designed especially for potting high voltage coils. The combination of low viscosity, excellent high temperature electrical properties and good thermal shock resistance makes this epoxy ideal for this application.
-
Vibra-Tite 934 Induction Cure Epoxy
Vibra-Tite 934 is a single-part induction cured epoxy adhesive with excellent adhesion to metal oily surfaces as well as composite materials. Can be used to enhance joint stiffness and joint durability. The high bond strength of this adhesive allows it to replace mechanical fasteners, soldering, brazing, or welding. Requires heat in the range of 120°C to 200°C. Vibra-Tite 934 is non-sagging allowing use with large gaps and on vertical surfaces.
-
-
Vibra-Tite 951 Pourable Aluminum Epoxy
Vibra-Tite 951 is a two component, aluminum filled epoxy for making molds, patterns, and holding fixtures. When the two components are properly mixed, the epoxy cures at room temperature to a silvery grey material that can be machined, drilled, sanded or tapped. Competes with Devcon Aluminum Liquid
-
Vibra-Tite 990 Flexible Toughened 2 Part Epoxy
Vibra- Tite 990 is a high viscosity, industrial grade epoxy adhesive with extended work life. This system forms a resilient, long work time adhesive with an easy mix ratio and good adhesion to thermoplastics. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.
Hand sanitizers now available. Consumer IPA and Ethanol. Dismiss