Product Country of Origin USA

  • Hot-Lock High temp threadlocker

    Hot-Lock™ Extreme High Temperature Threadlocker

    Vibra-Tite Hot-lock™ is a medium-high strength, ceramic based threadlocker which exhibits unparalleled temperature resistance up to 2000°F and excellent performance across many different substrate finishes.

  • VC-3 Tape

    VC-3 Tape Instant Threadlocker

    VC-3 Tape is a unique patent pending anti-vibration compound designed to prevent fastener loosening. Applied to the threads of a fastener and installed into a mating part; VC-3 Tape is ready for immediate use with no drying or curing time required. Unlike typical threadlockers, VC-3 Tape can be post assembly adjusted, removed, and re-used up to 3 times.

  • Vibra-Tite 603 Hand Sanitizer (IPA)

    Isopropyl Alcohol Antiseptic 75%. Topical Solution. Hand Sanitizer. Non-sterile Solution. For consumer use.

  • Vibra-Tite 604 Antiseptic Hand Rub (IPA)

    Isopropyl Alcohol Antiseptic 75%. Topical Solution. Anti-Septic Hand Rub. Non-sterile Solution. For Health Care Personnel.

  • Vibra-Tite 605 Hand Sanitizer (Ethanol)

    Alcohol Antiseptic 80%. Topical Solution. Hand Sanitizer. Non-sterile Solution. For consumer use.

  • Vibra-Tite 606 Antiseptic Hand Rub (Ethanol)

    Alcohol Antiseptic 80%. Topical Solution. Anti-Septic Hand Rub. Non-sterile Solution. For Health Care Personnel.

  • Isopropyl Alcohol 99 percent

    Vibra-Tite 614, IPA 99%, USP Grade Surface Sanitizer

    Isopropyl Alcohol 99%. USP Grade. Sanitizes and disinfects surfaces.

  • vibra-tite 111 threadlocker

    Vibra-Tite 111 Low Strength Threadlocker

    A low strength anaerobic threadlocker designed for locking threaded fasteners smaller than 1/4” in diameter, which require disassembly with standard hand tools. Also works on set screws, and screws that have a long engagement length.

  • 12150 Threadlocker Applied

    Vibra-Tite 121 Medium Strength Threadlocker

    A medium strength anaerobic threadlocker designed for locking threaded fasteners from 1/4” to 3/4” in diameter, that require disassembly with standard hand tools. Exhibits good temperature and solvent resistance.

  • Vibra-Tite 122 Oil Tolerant Threadlocker

    A medium strength, oil tolerant anaerobic threadlocker designed for locking threaded fasteners from 1/4” to 3/4” in diameter, that require disassemble with standard hand tools. Exhibits good temperature and solvent resistance.

  • Vibra-Tite 123 Medium Strength High Temp Threadlocker

    Typical uses include locking nuts or bolts ranging from 1/4” to 3/4” (6-20 mm) in diameter at continuous temperatures up to 450°F.

  • Hot

    Vibra-Tite 125 Medium Strength Gel Threadlocker

    A medium strength anaerobic gel threadlocker designed for locking threaded fasteners from 1/4” to 3/4” in diameter, that require disassembly with standard hand tools. Exhibits good temperature and solvent resistance. No-drip gel formula.

  • 13150 Threadlocker Applied

    Vibra-Tite 131 High Strength Threadlocker

    A high strength anaerobic threadlocker designed to permanently lock fasteners up to 1'' in diameter. Exhibits good temperature and solvent resistance.

  • Vibra-Tite 132 High Strength Primerless Threadlocker

    A high strength and high temperature threadlocker designed for permanently locking or sealing nuts and bolts up 1” diameter. Primerless, oil tolerant formula will cure even on passive materials such as stainless steel.

  • Vibra-Tite 135 High Strength Gel Threadlocker

    A high strength anaerobic gel threadlocker designed to permanently lock fasteners up to 1” in diameter. Exhibits good temperature and solvent resistance. No-drip gel formulation makes it easy to apply.

  • Vibra-Tite 137 High Temp/High Strength Threadlocker

    A high strength and high temperature anaerobic threadlocker designed to permanently lock fasteners up to 1 1/2'' in diameter. Joins threaded parts exposed to operating temperatures up to 450°F

  • Vibra-Tite 140 High Strength Threadlocker

    A high strength anaerobic threadlocker designed to permanently lock fasteners. Exhibits good temperature and solvent resistance. Performs on aluminum, steel, plated, stainless steel, and special alloy parts. Locks and seals fasteners from up to 1'' in diameter.

  • vibra-tite 141 threadlocker

    Vibra-Tite 141 High Strength Threadlocker

    A green general purpose threadlocker for permanent locking of threaded assemblies. 141 works on fasteners up to 1″ in diameter and seals against leakage and corrosion. It resists attack from most fuels, lubricants and industrial gases.

  • Vibra-Tite 146 Large Diameter/High Strength Threadlocker

    A high strength, large diameter anaerobic threadlocker designed to permanently lock fasteners. Resists attack from lubricants and most industrial liquids and gases.

  • Vibra-Tite 150 Medium Strength – Wicking Grade Threadlocker

    A fast cure, low viscosity wicking anaerobic threadlocker designed to seek voids in assembled components and cure anaerobically. Can be used as a post assembly application to prevent the loosening of metal threaded fasteners.

  • Viz-Torque applied to fastener assemblyVibra-Tite Viz-Torque 202 1 oz. Group

    Vibra-Tite Viz-Torque® 202

    Viz-Torque 202 Tamper Detection Marker is an inspection paste used to visually detect torque movement due to vibratory loosening or tampering of fittings, assemblies, nuts, bolts and studs. This quick-drying tamper proof torque marker identifies whether a part has been moved from its original position. Once dried in place, Viz-Torque 202 Tamper Detection Marker creates a seal for torque movement detection, which allows the dry and brittle material stripe to break, providing proof of fastener tampering or loosening. Viz-Torque 202 has good adhesion to most metals when applied to a clean, dry surface and is available in a selection of highly visible colors.

  • Vibra-Tite 208 Impact Resistant Light Cure Adhesive

    Dual cure impact resistant gel UV adhesive with excellent adhesion to most substrates.

  • Vibra-tite 20700CLR

    Vibra-Tite 207 UV/Anaerobic Dual Cure Adhesive and Sealant

    Vibra-Tite® 207 is a low viscosity UV/Anaerobic dual cure adhesive and sealant for sealing ammo.

  • vibra-tite 20900 light cure adhesive

    Vibra-Tite 209 Low Intensity UV Light Cure Adhesive

    Medium-High viscosity UV (light cure) adhesive with excellent adhesion to most substrate types.

  • Vibra-Tite 211 Glass Bonder Light Cure Adhesive

    Low viscosity glass bonder. Used to bond, seal or coat metal and glass components in industrial applications. Typical used include, but are not limited to, bonding electrical devices, appliance parts, and decorative components.

  • Hot

    Vibra-Tite VC-3 Threadmate

    Vibra-Tite VC-3 Threadmate is one of the most versatile threadlockers available on the market. An alternative to traditional liquid lockers which cure to form a hard bond, VC-3 is a proprietary blend of thermoplastic elastomer resins designed to remain flexible and absorb vibration. The combination of inert/non-reactive amorphous resins creates a tough, semi solid layer inside the threads of a mated joint. VC-3 damps the vibrational energy transferred between the threads of a mated fastener, preventing fastener loosening and loss of clamp load. These unique differences make VC-3 coated fasteners truly adjustable, removable, and reusable.

  • Vibra-Tite 215 Potting Light Cure Adhesive

    Vibra-Tite 215 is a uv curing, modified methacrylate ester adhesive with secondary heat cure. Vibra-Tite 215 is designed for UV potting and bonding glass to plastic substrates.

  • Vibra-Tite VC-4

    Vibra-Tite VC-4 exhibits similar performance to Vibra-Tite VC-3 except it contains a base solvent of Ethyl Acetate. VC-4 is one of the most versatile threadlockers available on the market. Unlike traditional liquid lockers which cure to form a hard bond, VC-4 is a blend of resins designed to remain flexible and absorb vibration. This unique difference makes VC-4 coated fasteners truly adjustable, removable, and reusable.

  • Vibra-Tite VC-5

    Vibra-Tite VC-5 exhibits similar performance to Vibra-Tite VC-3 except it contains a base solvent of Methyl Propyl Ketone. VC-5 is one of the most versatile threadlockers available on the market. Unlike traditional liquid lockers which cure to form a hard bond, VC-5 is a blend of resins designed to remain flexible and absorb vibration. This unique difference makes VC-5 coated fasteners truly adjustable, removable, and reusable.

  • Vibra-Tite VC-6

    Vibra-Tite VC-6 exhibits similar performance to Vibra-Tite VC-3 except it contains a base solvent of Dimethyl Carbonate. VC-6 is one of the most versatile threadlockers available on the market. Unlike traditional liquid lockers which cure to form a hard bond, VC-6 is a blend of resins designed to remain flexible and absorb vibration. This unique difference makes VC-6 coated fasteners truly adjustable, removable, and reusable.

  • Vibra-Tite 220 Glass Bonding Light Cure Adhesive

    Vibra-Tite 220 is a uv curing, modified methacrylate ester adhesive. It is designed for bonding glass to glass and glass to metal.

  • Vibra-Tite 224 High Impact Structural Adhesive

    Structural acrylic adhesive that is designed to bond a wide range of substrates such as metal, wood and some plastics. Use with structural activator, such as Vibra-Tite 638.

  • Vibra-Tite 225 No-Mix Structural Adhesive

    An activated Acrylic adhesive designed for fast fixturing on metal and ceramic materials. Applications include bonding metal or ceramic close fitting rigid parts which are exposed to thermal cycling, like motor assemblies.

  • Vibra-Tite 229 Glass Bonding Light Cure Adhesive

    Medium-High viscosity UV glass bonder for glass and some metal; cures optically clear.

  • Vibra-Tite 230 Impact Resistant Light Cure Adhesive

    Impact resistant multi-cure UV adhesive for glass and steel bonding.

  • Vibra-Tite 240 No-Mix Structural Adhesive

    An activated acrylic adhesive designed for fast fixturing on metal and magnet materials and a no mix system. Used in applications that require very fast assembly.

  • Vibra-Tite 250 Doming Plastics Light Cure Adhesive

    Vibra-Tite 250 is a single component, medium viscosity UV coating and structural adhesive suitable for bonding glass to glass or glass to plastic. It is suitable for use as a doming resin on glass and some plastics and composites. This product cures when exposed to ultraviolet radiation. When cured, it is highly resistant to vibration and impact forces.

  • Vibra-Tite 265 Tacking Light Cure Adhesive

    A medium viscosity light tacking UV adhesive for glass, steel and plastic.

  • Vibra-Tite 291 Acrylic UV – Visible w/Fluorescence Light Cure

    Low viscosity UV needle bonder for fiberglass, PS (polystyrene), ABS (Acrylonitrile Butyl Styrene), and acrylic.

  • Vibra-Tite 294 Plastic Bonding Light Cure Adhesive

    Medium viscosity UV (light cure) adhesive with excellent adhesion to most substrate types.

  • Vibra-Tite 297 Acrylic UV – Visible w/Fluorescence Light Cure

    Low viscosity UV (light cure) needle bonder that bonds well with PVC, Acrylic, and glass.

  • 42050 Thread Sealant Applied

    Vibra-Tite 420 Controlled Strength Thread Sealant

    An anaerobic thread sealing and thread locking compound with PTFE for pipe fittings. It is designed for sealing threaded fasteners that require disassembly with standard hand tools. It exhibits good temperature and solvent resistant.

  • Vibra-Tite 427 Medium Strength – Stainless Steel Thread Sealant

    Prevents leakage and loosening from shock and vibration. Particularly suitable for stainless steel.

  • Vibra-Tite 440 Pneumatic / Hydraulic Sealant Thread Sealant

    A fast curing high strength anaerobic sealant which seals hydraulic and pneumatic fittings up to 2″ in diameter, resisting high pressures and vibrational loosening.

  • Vibra-Tite 442 Gel Thread Sealant

    Vibra-Tite 442 Hydraulic Fast Cure Gel Sealant

    A fast curing gel thread selant which withstands temperatures up to 300°F (149°C).

  • Vibra-Tite 444 Hydraulic Sealant – High Pressure Thread Sealant

    A medium strength anaerobic sealant which seals hydraulic and pneumatic fittings up to 2″ in diameter, resisting high pressure and vibrational loosening.

  • Vibra-Tite 446 Refrigerant Sealant – High Pressure Thread Sealant

    Optimum resistance to solvents and refrigerants. Excellent chemical resistance on threaded connections handling ammonia, fluorocarbons and halides. Provides an instant seal between threaded fittings. Uncured sealant is miscible with hydraulic fluid and will not clog filter and other components in hydraulic systems.

  • 46050 Thread Sealant Applied

    Vibra-Tite 460 High Temp/Stainless Steel Thread Sealant

    Sets fast to give an instant low pressure seal of 100 psi and a high pressure seal when fully cured. This high strength product provides 100% sealing capability and does not shrink after curing, unlike more traditional solvent based pipe dopes. Contains PTFE.

  • DriveGrip for screw heads
    Hot

    Vibra-Tite DriveGrip

    Use DriveGrip and throw away your easy-outs, speed outs, reverse drill bits, and other screw extractors. DriveGrip is an anti cam-out fluid made of an inert liquid metallic grit, a drop of which is placed in the recessed head of a fastener before use. Immediately after application you can use your screw driver as normal, but will notice a significant reduction in the amount of effort it takes to prevent the driver from slipping. This is because DriveGrip works by creating additional friction between the fastener head and driver (up to 700% more!). It's so easy to use and so effective that you will be shocked you had never heard of it before.

  • Vibra-Tite 480 Multi-Purpose FBC Thread Sealant

    Vibra-Tite 480 Multi-Purpose – FBC Compatible Thread Sealant with PTFE is designed to lubricate and seal threaded connections. A non-curing and non-toxic formula, Vibra-Tite 480 contains no lead or harmful metals and can be used in potable water systems.

  • Non-Curing Thread Sealant

    Vibra-Tite 486 Non-Hardening Thread Sealant

    Vibra-Tite 486 Non-Curing Thread Sealant with PTFE is a creamy white paste for general purpose pipe and thread sealing. Typical applications include sealing threaded pipes, pipe fittings and flanges to seal against liquids and gases.

  • Vibra-Tite 530 General Purpose Retaining Compound

    The product performs on aluminum, steel, plated, stainless steel, and special alloy parts. Can be used where lubricity is needed to press fit parts or to create an air-tight seal on cylindrical assemblies. This product cures rapidly on all metal surfaces. Replaces press fit assemblies and keyways. Used on gearbox bolts / drive shaft, bearing applications.

  • Vibra-Tite 535 General Purpose – Gel Retaining Compound

    A controlled, high strength anaerobic gel retaining compound with good temperature and solvent resistance. Replaces press fit assemblies and keyways. Used on gearbox bolts / drive shaft, bearing applications.

  • Vibra-Tite 538 High Strength Retaining Compound

    A high strength, room curing anaerobic retaining compound that resists axial and radial loading.

  • vibra-tite 541 retaining compound

    Vibra-Tite 541 High Strength – Slip Fit Retaining Compound

    A high strength, high viscosity, anaerobic retaining compound used for bonding rigid assemblies of all types. This material can be used effectively to increase the strength of most mechanical assemblies. Locks keys and splines. Eliminates backlash in worn assemblies. Locks bearings in place, preventing spin out. Bonds rotor to shaft in low horsepower motors. Locks bushings and sleeves in housings.

  • Vibra-Tite 542 High Strength – Large Gap Retaining Compound

    A high strength, high viscosity, anaerobic retaining compound used for bonding rigid assemblies of all types. This material can be used effectively to increase the strength of most mechanical assemblies. Locks keys and splines. Eliminates backlash in worn assemblies. Locks bearings in place, preventing spin out. Bonds rotor to shaft in low horsepower motors. Locks bushings and sleeves in housings.

  • Vibra-Tite 546 Impact Resistant Retaining Compound

    A quick fixturing high strength flexible, anaerobic retaining compound designed to bond metal cylindrical assemblies. Exhibits excellent temperature and solvent resistant. The product performs on aluminum, steel, plated, stainless steel, and special alloy parts. Locks shaft and hubs together for gears, bearing, bushings. Bonds pins, adaptors, plugs.

  • Vibra-Tite 548 Rapid Curing Retaining Compound

    A medium viscosity, quick curing, high strength anaerobic retaining compound designed for tight-clearance, and slip-fit metal applications. Exhibits excellent temperature and solvent resistant. The product performs on aluminum, steel, plated, stainless steel, and special alloy parts.Locks shaft and hubs together for gears, bearing, bushings. Bonds pins, adaptors, plugs.

  • Vibra-Tite 550 Core Plug Sealant Retaining Compound

    A high strength anaerobic retaining compound designed for freeze, core, and cup plug applications. Used to seal core plugs in upper and lower manifolds and engine blocks. Typical applications include core plugs and cup plugs installed into engine blocks.

  • Vibra-Tite 560 High Strength – High Temperature Retaining Compound

    A high strength, high temperature, anaerobic retaining compound used for bonding rigid assemblies of all types. This material can be used effectively to increase the strength of most mechanical assemblies. The product performs on aluminum, steel, plated, stainless steel, and special alloy parts.Locks shaft and hubs together for gears, bearing, bushings. Bonds pins, adaptors, plugs.

  • Vibra-Tite 566 Gap Filling – For Worn Parts Retaining Compound

    A high viscosity, general purpose, anaerobic retaining compound used for press-fit and tight-clearance, and slip-fit metal applications. Exhibits good temperature and solvent resistance. The product performs on aluminum, steel, plated, stainless steel, and special alloy parts.

  • Vibra-Tite 567 High Temperature – Large Gap Retaining Compound

    A high temperature, high strength, large gap filling anaerobic retaining compound designed for metal cylindrical assembly applications. Exhibits excellent temperature and solvent resistant. The product performs on aluminum, steel, plated, stainless steel, and special alloy parts.Locks shaft and hubs together for gears, bearing, bushings. Bonds pins, adaptors, plugs.

  • Vibra-Tite 600 Excel Structural Activator

    Vibra-Tite Excel 600 Activator is a fast-curing, resin-based material designed for use with Vibra-Tite structural adhesives. The adhesive is applied on one surface and the activator on the other, no mixing required. The activator undergoes a chemical reaction when in contact with the adhesive and polymerizes to form part of the bond. It contains 100% active ingredients.

  • vibra-tite 611 primer

    Vibra-Tite 611 Excel Primer N

    General purpose primer. Significantly speeds up the cure time of anaerobic threadlockers when assembling metal parts that are cold, have large gaps or deep threads. Primers are recommended when assembling metal parts with inactive surfaces such as stainless, galvanized steel and zinc.

  • vibra-tite 612 primer

    Vibra-Tite 612 Excel Primer T

    Fast acting primer. Significantly speeds up the cure time of anaerobic threadlockers when assembling metal parts that are cold, have large gaps or deep threads. Primers are recommended when assembling metal parts with inactive surfaces such as stainless, galvanized steel and zinc.

  • vibra-tite 621 primer for superglue

    Vibra-Tite 621 Excel CA Accelerator

    Used to improve gap-filling abilities of cyanoacrylate adhesives and to speed the cure of high-viscosity cyanoacrylate adhesives.
    Eliminates the need to fixture parts.

  • vibra-tite 623 primer for superglue

    Vibra-Tite 623 Excel General Accelerator

    General purpose accelerator. 623 General Purpose Accelerator is an ozone friendly accelerator used for normal curing of cyanoacrylates and to prepare the surface for bonding. Excel 623 is also designed to provide a fast cure of thick deposits of SuperGlues or for post curing excess adhesive outside of the bond line.

  • vibra-tite 624 primer for superglue

    Vibra-Tite 624 Excel Cyanoacrylate Accelerator

    Excel 624 is an ozone friendly accelerator used for normal curing of cyanoacrylates and to prepare the surface for bonding. Excel 624 is an isopropanol based accelerator that will whiten the adhesive's exterior bondline for easy inspection, and will not crack polycarbonate.

  • Vibra-Tite 625 Excel Polyolefin Primer

    Use Excel 625 Primer for difficult-to-bond plastics. Apply primer to prepare polyolefin or other low-energy surfaces for cyanoacrylate bonding.

  • Vibra-Tite 626 Excel Polyolefin Primer

    Excel 626 General Purpose Accelerator is an acetone based accelerator used for normal curing of cyanoacrylates and to prepare the surface for bonding. Excel 626 is designed to provide a fast cure of thick deposits of SuperGlues or for post curing excess adhesive outside of the bond line.

  • Vibra-Tite 638 Excel Structural Activator

    General structural activator. Initiates the cure of structural acrylic adhesives, such as Vibra-Tite 224.

  • super glue cleaner

    Vibra-Tite 642 Cyanoacrylate Remover

    • Dissolves and removes the dried super glue (cyanoacrylates) adhesives
    • Removes glue from skin, metal, stone, glass, & more
    • Perfect for the home, workshop, and garage to dissolve dried glue
    • Better than acetone for dissolving glue
    • Made in the usa
  • Vibra-Tite 709 Flexible Gasket Maker

    Vibra-Tite 709 Flexible Gasket Maker

    Provides resistance to low pressures after assembly of flanges.  Seals between rigid metal surfaces and flanges such as valve covers and gearbox casings. Can be used with or without pre-cut, pre-formed gaskets.

  • Vibra-Tite 710 High Temperature Rigid Flange Sealant Gasket Maker

    Vibra-Tite 710 Gasket Maker is a single component, medium strength, thixotropic, anaerobic sealant which cures when confined between close fitting metal surfaces. Provides an instant low pressure seal. This product can be used with or without pre-cut, pre-formed gaskets.

  • vibra-tite 724 gasket maker

    Vibra-Tite 724 Fast Flange Sealant Gasket Maker

    Single component, medium strength, thixotropic, anaerobic sealant. Provides a fast low pressure seal between rigid metal faces and flanges and is suitable as a replacement for a variety of pre-formed or pre-cut gastkets. The thixotropic behavior of this material minimizes migration of material following application.

  • Vibra-Tite 730 Flexible Solvent Resistant Gasket Maker

    High viscosity, single component, medium strength, thixotropic, anaerobic sealant which cures when confined between close fitting metal surfaces. Provides an instant low pressure seal. Seals joints between rigid metal faces and flanges such as valve covers and gearbox casings.

  • Vibra-Tite 732 Flexible Gasket Maker

    A tough flexible formed-in-place gasket. Provides an instant low pressure seal. For fuel and water pumps, split crank cases on engines, gearbox covers, engine thermostats, air compressor end caps, chainsaws, lawn mowers etc.

  • vibra-tite polyurethane

    Vibra-Tite 801 Urethane

    Vibra-Tite 801 is a 1-component liquid adhesive based on polyurethane. It is a moisture-curing, long open time structural assembly system. Unlike contact adhesives, which require the coating of both substrate surfaces, Vibra-Tite 801 requires only a single side. There is no need for additional handling and expensive drying ovens to flash off solvents before engaging the bond.

  • vibra-tite polyurethane

    Vibra-Tite 801FC Fast Curing Urethane

    Versatile urethane for bonding wood, metal glass, stone, brick, fiberglass, carbon, foam and more. 100% waterproof. Temperature resistant. Sandable, paintable, stainable. Low foam.

  • vibra-tite polyurethane

    Vibra-Tite 801SS Stainless Steel Urethane

    Versatile urethane for bonding wood, metal glass, stone, brick, fiberglass, carbon, foam and more. 100% waterproof. Temperature resistant. Sandable, paintable, stainable. Low foam.

  • vibra-tite polyurethane

    Vibra-Tite 802 Polyurethane

    Vibra-Tite 802 is a 2-component lamination adhesive system based on polyurethane. Vibra-Tite 803 HARDENER is a polyol blend which can be colored with pigment, and Vibra-Tite 802 RESIN is a formulated isocyante with exceptional bonding and sealing properties to provide exceptional adhesion to a wide variety of engineering plastics, metals or other substrates. This system can be used with plural component extrusion equipment, or standard 1:1 meter mix (volumetric) dispensing machines that use static mixers. Its mixed viscosity of ~3500 cps at 75°F allows Vibra-Tite 802 to be spray applied using heavy particle size atomization process.

  • Vibra-Tite 816 Hybrid Structural

    Vibra-Tite 816 is a high performance, multipurpose structural adhesive/sealant designed for difficult bonding and sealing applications. It is a moisture curing sealant developed for industrial uses requiring elasticity, high immediate green strength and excellent adhesion. Non-sagging but easy to gun/apply in field installations.

  • Vibra-Tite 817 Hybrid Structural

    Vibra-Tite 817 is a high performance, multipurpose structural adhesive/sealant designed for difficult bonding and sealing applications. It is a moisture curing sealant developed for industrial uses requiring elasticity, high immediate green strength and excellent adhesion. Non-sagging but easy to gun/apply in field installations.

  • Vibra-Tite 825 Structural

    Vibra-Tite 825 is an economical, multipurpose structural adhesive/sealant designed for difficult bonding and sealing applications. It is a moisture curing sealant developed for industrial uses requiring elasticity, high immediate green strength and excellent adhesion. Non-sagging but easy to gun / apply in field installations.

  • Vibra-tite 90550 epoxy

    Vibra-Tite 905 Quick Cure 2 Part Epoxy

    Vibra-Tite 905 is a fast setting adhesive that cures at temperatures as low as 41°F/5°C. For bonding and repairing small parts.

  • Vibra-Tite 906 Marine Grade Anti-Seize

    Protects assemblies exposed to fresh and salt water. Works well in high-humidity conditions. Has no metals and is not a marine pollutant. Contains Molybdenum Disulfide for extreme pressure applications. Use in extreme temperatures up to 2,600°F (1,427°C).

  • Vibra-Tite 9070 Aluminum Anti-Seize

    Ideal for all metals. Prevents seizing, galling, pitting, excessive wear, and corrosion. The lubricating formulation is a protective paste consisting of find flakes of graphite suspended in a blend of lubricants and oils.

  • Vibra-Tite 9071 Copper Anti-Seize

    Ideal for softer metals. Prevents seizing, galling, pitting, excessive wear, and corrosion. The lubricating formulation is a protective paste consisting of fine flakes of copper and graphite suspended in a blend of lubricants and oils.

  • Vibra-Tite 9072 Nickel Anti-Seize

    Ideal for extreme temperatures. Prevents seizing, galling, pitting, excessive wear, and corrosion. Copper and graphite free base. Resistant to harsh chemical environments. Excellent for stainless steel and other metal fittings.

  • vibra-tite food grade anti-seize

    Vibra-Tite 908 Food Grade Anti-Seize

    Vibra-Tite Food Grade Anti-Seize is specifically developed for use in applications where incidental food contact is possible. Protects metal parts from seizure, galling, rust, corrosion and heat freeze by adhering to the metal surface. Meets NSF (H1)

  • Vibra-Tite 910G 5-Minute Two Part Epoxy

    A 2-part system forms a strong bond when cured. 4-6 minutes of positioning time and can be handled in 1 hour. Formulated as a gel, which makes it idea for both vertical and horizontal surfaces. Green color is the combination of blue resin and yellow hardener. Once correctly mixed they will combine to a green color.

  • Vibra-Tite 911 Epoxy

    Epoxy VIBRA-TITE 911 is a fast setting adhesive that cures at temperatures as low as 41°F/5°C. For bonding and repairing small parts. Competes with Fastweld 10

  • Vibra-Tite 913 Epoxy

    Epoxy Vibra-Tite 913 is an extremely strong, medium cure, water-resistant clear adhesive that will self-level after application. This compound is intended to bond parts in a structural environment or potting electronic components and assemblies.  Competes with Devcon’s 2 ton epoxy

  • Vibra-Tite 915 Epoxy

    VIBRA-TITE 915 is a low-viscosity general purpose potting compound that is designed to form a resilient, long work time potting compound with good surface finish and bond strength to thermoplastics. Competes with Hysol E-60NC

  • Vibra-Tite 916 Epoxy

    VIBRA-TITE 916 is a toughened, medium viscosity, industrial grade epoxy adhesive. Once mixed, the two component epoxy cures at room temperature to form a tough, off-white, bond line that provides high adhesive strength.  Competes with Hysol E-60HP

  • Vibra-Tite 920 High Peel / High Shear 2 Part Epoxy

    Vibra-Tite 920 is a medium viscosity, industrial grade epoxy adhesive with extended work life. This system forms a good adhesion to thermoplastics with high peel and shear strength. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.

  • Vibra-Tite 921 Plastic Bonding Epoxy

    Vibra-Tite 921 is a medium viscosity, industrial grade epoxy adhesive with extended work life. This system forms a good adhesion to thermoplastics with high peel and shear strength. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.

  • Vibra-Tite 923 Aluminum Bonding Epoxy

    Vibra-Tite 923 is a toughened, medium viscosity, industrial grade epoxy adhesive. Once mixed, the two component epoxy cures at room temperature to form a tough, off-white, bond line that provides high adhesive strength.

  • Vibra-Tite 924 Epoxy

    Vibra-Tite 924 is a general purpose, medium viscosity, two-component epoxy adhesive system used for applications which require strong, durable, chemically and environmentally resistant bonds, high viscosity, with an extended work life. This system forms a resilient, long work time adhesive with an easy mix ratio and good adhesion to thermoplastics. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance. Competes with Lord 305

  • vibra-tite epoxy 927

    Vibra-Tite 927 Medium Viscosity / High Strength 2 Part Epoxy

    A toughened, medium viscosity, industrial grade epoxy adhesive. Once mixed, the two component epoxy cures at room temperature to form a tough, off-white, bond line that provides high adhesive strength.

  • Vibra-Tite 941 Epoxy

    Vibra-Tite 941 is a medium-viscosity general purpose two-part epoxy compound that is designed to form a resilient encapsulant with good surface finish and high bond strength to thermoplastics. Vibra-Tite 941 is recommended when potting assemblies with narrow gaps and tight spaces.

  • Vibra-Tite 942 Epoxy

    Vibra-Tite 942 is a filled, low shrinkage version of Vibra-Tite 941 general purpose encapsulating compound.  Designed to form a resilient encapsulant with good surface finish and high bond strength to thermoplastics,  Vibra-Tite 942 is recommended when potting assemblies with narrow gaps and tight spaces.

  • Vibra-Tite 932 Encapsulating Epoxy

    Vibra-Tite 932 is two-part epoxy encapsulant and adhesive. This system forms a resilient, long work time potting and encapsulant material with an easy mix ratio and good adhesion to thermoplastics. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.

  • Vibra-Tite 933 Ignition Coil Impregnation and Encapsulation Epoxy

    Vibra-Tite 933 is a long working life, heat curing, and two component formulation. It was designed especially for potting high voltage coils. The combination of low viscosity, excellent high temperature electrical properties and good thermal shock resistance makes this epoxy ideal for this application.

  • Vibra-Tite 934 Induction Cure Epoxy

    Vibra-Tite 934 is a single-part induction cured epoxy adhesive with excellent adhesion to metal oily surfaces as well as composite materials. Can be used to enhance joint stiffness and joint durability. The high bond strength of this adhesive allows it to replace mechanical fasteners, soldering, brazing, or welding. Requires heat in the range of 120°C to 200°C. Vibra-Tite 934 is non-sagging allowing use with large gaps and on vertical surfaces.

  • vibra-tite 935 epoxy

    Vibra-Tite 935 Low Viscosity General Purpose Potting 2 Part Epoxy

    Vibra-Tite 935 is a low-viscosity general purpose potting compound that is designed to form a resilient, long work time potting compound with good surface finish and bond strength to thermoplastics.

  • Vibra-Tite 951 Pourable Aluminum Epoxy

    Vibra-Tite 951 is a two component, aluminum filled epoxy for making molds, patterns, and holding fixtures. When the two components are properly mixed, the epoxy cures at room temperature to a silvery grey material that can be machined, drilled, sanded or tapped.  Competes with Devcon Aluminum Liquid

  • Thermal Defender® TD-97

    TD-97 is a dry film ceramic coating which is sprayed onto parts to protect them from metal weld spatter. Quick and easy, it can be applied and dried in under a minute and is then ready for immediate use.

  • Vibra-Tite 989 Multi-Purpose Polyurethane

    Vibra-Tite 989 Multi-Purpose Polyurethane

    Versatile urethane for bonding wood, metal glass, stone, brick, fiberglass, carbon, foam and more. 100% waterproof. Temperature resistant. Sandable, paintable, stainable. Low foam.

  • Vibra-Tite 990 Flexible Toughened 2 Part Epoxy

    Vibra- Tite 990 is a high viscosity, industrial grade epoxy adhesive with extended work life. This system forms a resilient, long work time adhesive with an easy mix ratio and good adhesion to thermoplastics. It will cure rapidly with heat to produce a material with excellent chemical, heat, and moisture resistance.

  • Vibra-Tite 992 Copper RTV Silicone

    Vibra-Tite 992 Copper RTV Silicone Gasket Maker

    A one-part neutral cure silicone sealant with high temperature resistance that cures in the presence of atmospheric moisture to produce a durable and flexible silicone rubber compound.

  • Vibra-Tite 99330 Silicone

    Vibra-Tite 993 Heavy Body Black Silicone Gasket Maker

    A one-part neutral cure silicone sealant with high temperature resistance that cures in the presence of atmospheric moisture to produce a durable and flexible silicone rubber compound.

  • Vibra-Tite 99530 Silicone

    Vibra-Tite 995 Clear RTV Silicone Sealant

    A one-part general purpose acetoxy cure silicone sealant that cures in the presence of atmospheric moisture to produce a durable and water proof flexible silicone rubber compound. Resists oil, water, weather, vibration, grease. Seals, bonds, repairs, mends and secures glass, metal, plastics, fabric, vinyl.

  • Vibra-Tite 99630 Silicone

    Vibra-Tite 996 Red RTV Silicone Gasket Maker

    A one-part acetoxy cure silicone sealant with high temperature resistance that cures in the presence of atmospheric moisture to produce a durable and flexible silicone rubber compound.

  • Vibra-Tite 997 Blue RTV Silicone

    Vibra-Tite 997 Blue RTV Silicone Gasket Maker

    A one-part neutral cure silicone sealant with high temperature resistance that cures in the presence of atmospheric moisture to produce a durable and flexible silicone rubber compound.

  • Vibra-Tite 998 Black RTV Silicone

    Vibra-Tite 998 Black RTV Silicone Gasket Maker

    A one-part acetoxy cure silicone sealant with high temperature resistance that cures in the presence of atmospheric moisture to produce a durable and flexible silicone rubber compound.

  • Vibra-Tite 999 Grey RTV Silicone Gasket Maker

    A one-part neutral cure silicone sealant with high temperature resistance that cures in the presence of atmospheric moisture to produce a durable and flexible silicone rubber compound.

  • vibra-tite pb 300 structural adhesive

    Vibra-Tite PB300 MMA – All Purpose – Fast Set

    General purpose. Adheres to most substrates. Rapid cure time. No surface preparation. High strength. High modulus. 100% reactive. Excellent resistance to hydrocarbons, acids and bases (3-10 pH), and salt solutions. Use on ABS, Acrylics, Epoxies, FRP, Gelcoats, Polyesters, PVC, Polystyrene, Urethanes, and Vinyl Esters.

  • vibra-tite pb 305 structural adhesive

    Vibra-Tite PB305 MMA – All Purpose – Extremely Fast Set

    Vibra-Tite PB305 is a fast setting, high performance two part methacrylate adhesive engineered to bond a wide range of materials including metals, plastics, and especially fiberglass. It offers outstanding bond strength, is extremely durable, and exhibits excellent impact and weathering properties. Vibra-Tite PB305 greatly increases the reliability of finished assemblies with exceptional flexibility and its ability to with stand extreme temperature fluctuation and thermal cycling.

  • vibra-tite pb 310 structural adhesive

    Vibra-Tite PB310 MMA – All Purpose – High Strength

    Vibra-Tite PB310 is a high performance two part methacrylate adhesive engineered to bond a wide range of materials including metals, plastics,and fiberglass. It offers outstanding bond strength, is extremely durable, and exhibits excellent impact and weathering properties. Vibra-Tite PB310 greatly increases the reliability of finished assemblies with exceptional toughness and its ability to with stand extreme temperature fluctuation and thermal cycling.

  • vibra-tite pb 320 structural adhesive

    Vibra-Tite PB320 MMA – All Purpose – Medium Set

    Vibra-Tite PB320 is a toughened, medium cure speed, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.

  • vibra-tite pb 330 structural adhesive

    Vibra-Tite PB330 MMA – All Purpose – Medium Set

    Vibra-Tite PB330 is a high performance two part methacrylate adhesive engineered to bond a wide range of materials including metal and plastics, especially fiberglass. It offers a moderate amount of open time, outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation,  thermal cycling, and chemical / environmental resistance.

  • vibra-tite pb 405 structural adhesive

    Vibra-Tite PB405 MMA – All Purpose – Extremely Fast Set

    Vibra-Tite PB405 is a high performance two part fast setting methacrylate adhesive, engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, quick setting, and excellent impact and elastic properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental conditions.

  • vibra-tite pb 420 structural adhesive

    Vibra-Tite PB420 MMA – All Purpose – Fast Set Time

    Vibra-Tite PB420 is a toughened, fast setting, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.

  • vibra-tite pb 422 structural adhesive

    Vibra-Tite PB422 MMA – All Purpose – Slow Set

    Vibra-Tite PB422 is a toughened, slow setting, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.

  • vibra-tite pb 425 structural adhesive

    Vibra-Tite PB425 MMA – All Purpose – Long Set

    Vibra-Tite PB425 is a toughened, slow setting, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.

  • vibra-tite pb 530 structural adhesive

    Vibra-Tite PB530 MMA – All Purpose – Moderate Set

    Vibra-Tite PB530 is a toughened, medium setting, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.

  • vibra-tite pb 550 structural adhesive

    Vibra-Tite PB550 MMA – Marine – U.V. Stable

    Vibra-Tite PB550 is a toughened, UV stable, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.

  • Vibra-tite PB50050 Structural Adhesive

    Vibra-Tite PB500 MMA – Low Surface Energy Bonder

    Vibra-Tite PB500 is a 2-part methacrylate based adhesive that is specially formulated to bond low surface energy materials such as polypropylene, polyethylene and PTFE without additional surface preparation. The PB500 offers increased working time while also building ultimate strength faster than other adhesives in its class. The PB500 material offers high impact resistance and is capable of withstanding extreme temperature fluctuations.

  • vibra-tite pb 560 structural adhesive

    Vibra-Tite PB560 MMA – All Purpose – Long Set Time

    Vibra-Tite PB560 is a toughened, slow set, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.

  • vibra-tite pb 950 structural adhesive

    Vibra-Tite PB590 MMA – All Purpose – Longest Set Time

    Vibra-Tite PB590 is a toughened, very slow setting, high performance two part methacrylate adhesive engineered to bond a wide range of plastics, metals, and composite assemblies. It offers outstanding bond strength, extreme durability, and excellent impact and weathering properties. Greatly increases the reliability of finished assemblies with its ability to withstand extreme temperature fluctuation, thermal cycling, and chemical / environmental resistance.